Page 4 of 6 FirstFirst ... 23456 LastLast
Results 31 to 40 of 56

Thread: DISCO will not Turn Over - Help?

  1. 21st August 2009, 05:53 PM #31
    Byte
    Byte is offline Master
    Join Date
    Apr 2009
    Posts
    105
    Total Downloaded
    0
    OK - I was abe to pull the pump, spray clean some terminals and then re-install it and the infamous red external thread ring.

    pump now works because i can hear the 10 sec whirl sound and voltage tested as well.

    Car still not run however but does turn over.

    I need to locate my displaced spark plug spanner tool to undo the plug to see if it is wet. Damn - I need to buy yet another plug spannner!!

    What happens if plug is still dry?

    THoguhts?

    Byte
    Reply With Quote Reply With Quote
  2. 21st August 2009, 06:11 PM #32
    Pierre
    Pierre is offline Wizard Silver Subscriber
    Join Date
    Jan 1970
    Location
    Blairgowrie, Vic
    Posts
    1,106
    Total Downloaded
    0
    Got spark? Perhaps the infamous ignition module intermittent (then terminal) failure?

    If you got fuel pressure (fuel pump working, shraeder valve test yields fuel), then at crank, check for spark with spare plug, timing light, etc.

    Good luck, watching with interest.

    BTW, where are you?

    Cheers

    Pete
    Dizzie, 08 D3 TDV6 SE
    Reply With Quote Reply With Quote
  3. 22nd August 2009, 09:32 AM #33
    Byte
    Byte is offline Master
    Join Date
    Apr 2009
    Posts
    105
    Total Downloaded
    0
    Hi Pirre.

    i live in adelaide.

    where is this infamous ignition module located ?

    will obtain a new plug spnnaer today in dig in../ report back.

    Byte
    Reply With Quote Reply With Quote
  4. 22nd August 2009, 04:06 PM #34
    Byte
    Byte is offline Master
    Join Date
    Apr 2009
    Posts
    105
    Total Downloaded
    0
    OK - got myself another plug spanner.

    I try to turn but will not budge.

    Before I strip threads, can someone please advise/confirm which way I should turn the plugs to remove them from block (CCW or CW)?

    Byte
    Reply With Quote Reply With Quote
  5. 22nd August 2009, 04:14 PM #35
    rovercare's Avatar
    rovercare
    rovercare is offline OldBushie
    Join Date
    Jan 1970
    Location
    Yinnar South, Vic
    Posts
    9,943
    Total Downloaded
    0
    Quote Originally Posted by Byte View Post
    OK - got myself another plug spanner.

    I try to turn but will not budge.

    Before I strip threads, can someone please advise/confirm which way I should turn the plugs to remove them from block (CCW or CW)?

    Byte
    Anti clockwise, lefty loosey, righty tighty
    Reply With Quote Reply With Quote
  6. 22nd August 2009, 04:42 PM #36
    Byte
    Byte is offline Master
    Join Date
    Apr 2009
    Posts
    105
    Total Downloaded
    0
    OK - plugs pulled - still dry.

    I also took a plug out - then reconnected it's lead and then located it close to chassis and then i got the wife to crank it over - no spark.

    I don't know if I correclty diagnosed the spark problem - can someone pease confirm.

    So, what now? I hear fuel pump working but seems to be no fuel flow to engine and no apparent spark.

    where is this infamous ignition module located ?

    How do i diagnose this module?

    Yes - fuel pump fuse re-checked and not broken....

    Help??

    Byte
    Reply With Quote Reply With Quote
  7. 23rd August 2009, 08:14 AM #37
    Byte
    Byte is offline Master
    Join Date
    Apr 2009
    Posts
    105
    Total Downloaded
    0
    need your help here guys...
    Reply With Quote Reply With Quote
  8. 23rd August 2009, 08:28 AM #38
    dullbird's Avatar
    dullbird
    dullbird is offline Admin Gold Subscriber
    Join Date
    Jan 1970
    Location
    Down the road from Sydney
    Posts
    14,702
    Total Downloaded
    0
    fuel filter couldn't be blocked could it?

    if your pumps working but you dont have fuel....would it be possible for a blockage somewhere
    Our Land Rover does not leak oil! it just marks its territory.......



    Reply With Quote Reply With Quote
  9. 23rd August 2009, 12:43 PM #39
    Byte
    Byte is offline Master
    Join Date
    Apr 2009
    Posts
    105
    Total Downloaded
    0
    Where is the fuel filter located?

    Byte
    Reply With Quote Reply With Quote
  10. 23rd August 2009, 12:51 PM #40
    justinc's Avatar
    justinc
    justinc is offline Swaggie Vendor
    Join Date
    Aug 2006
    Location
    Kingston, Tassie, OZ.
    Posts
    13,728
    Total Downloaded
    0
    No spark could also be the electrical connection at the distributor, unplug it and check that the plug isn't corroded etc, and the module is just under the coil, LHF engine compartment. Have you got a multimeter? You need to have a minimum of 12v at the pos of the coil,(Plastic black female plug side of the coil) with ignition switched on. If not, then supply a 12v supply to the coil directly from the battery and try cranking again.
    Report back

    JC
    The Isuzu 110. Solid and as dependable as a rock, coming soon with auto box😊
    The Range Rover L322 4.4.TTDV8 ....probably won't bother with the remap..😈
    Reply With Quote Reply With Quote
Page 4 of 6 FirstFirst ... 23456 LastLast
« 1. Absorption canister and purge valve. | 97 TDI windscreen »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!