Page 1 of 9 123 ... LastLast
Results 1 to 10 of 83

Thread: D3 stuck on it's guts

  1. 13th November 2014, 06:14 PM #1
    daneprocter Guest

    Unhappy D3 stuck on it's guts

    So yesterday evening I had to change the front prop shaft in my 05 LR3. All mechanical stuff went according to plan, however, I left the ignition on the whole time and the battery went flat. After getting the car going again (jump started it off my old mans LR4) I am getting a suspension error and it won't lift up from it's lowest setting.

    I have a llams kit which I have switched off and tried several times to clear the codes with my nanocom, but the fault still comes back.

    I had it in super extended mode (so I could fit under the truck) while I did the work so I don't think it could be a leak.

    Is there something I can do to reset the suspension? It still drives normally, except for excessive bouncing on the bump stops.

    If you could point me in the right direction or share some information, It would be muchly appreciated!
    Reply With Quote Reply With Quote
  2. 13th November 2014, 06:24 PM #2
    Epic pooh's Avatar
    Epic pooh
    Epic pooh is offline Master
    Join Date
    Feb 2012
    Location
    Wollongong
    Posts
    773
    Total Downloaded
    0
    Charge your battery, do a hard reset and it will probably be back to normal.
    Reply With Quote Reply With Quote
  3. 13th November 2014, 06:29 PM #3
    Graeme
    Graeme is offline Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,033
    Total Downloaded
    0
    Are the raise and lower LEDS flashing? If so, press the raise button.

    What fault does the Nanocom show?
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
  4. 13th November 2014, 06:32 PM #4
    daneprocter Guest
    Quote Originally Posted by Epic pooh View Post
    Charge your battery, do a hard reset and it will probably be back to normal.
    Battery has been charged. Sorry for my ignorance, but what is a hard reset?
    Reply With Quote Reply With Quote
  5. 13th November 2014, 06:35 PM #5
    daneprocter Guest
    I've just disconnected the batteries to double check they are properly charged.
    I can't remember if the lights were flashing, I will check again when I connect the batteries up again.
    The light on the dash that has been orange when other faults occurred has turned red.
    I'll hook the batteries up and check again.
    Reply With Quote Reply With Quote
  6. 13th November 2014, 06:39 PM #6
    Graeme
    Graeme is offline Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,033
    Total Downloaded
    0
    You will need to get the fault codes.
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
  7. 13th November 2014, 06:58 PM #7
    daneprocter Guest
    Quote Originally Posted by Graeme View Post
    Are the raise and lower LEDS flashing? If so, press the raise button.

    What fault does the Nanocom show?
    The lights aren't flashing. There is a red one on the dash.
    I got a control module error on the nanocom and a c431 error. The rear is going up and down but the front is stuck at the lowest setting
    Reply With Quote Reply With Quote
  8. 13th November 2014, 07:17 PM #8
    Graeme
    Graeme is offline Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,033
    Total Downloaded
    0
    When did you get the Llams? If it was before about April this year then it needs a cable-tie to hold the 2 grey connectors together. Those connectors are for the front so suggests a possible cause but nothing to do with the work just completed or a flat battery.
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
  9. 13th November 2014, 07:31 PM #9
    daneprocter Guest
    I can't remember when I bought it, but I've only had the car for a bit over a month.
    I've run out of light and organised a hire car to get to work tomorrow. Will have another crack at it tomorrow arvo. Might take the llams out and see if that does anything.
    Reply With Quote Reply With Quote
  10. 13th November 2014, 07:45 PM #10
    Graeme
    Graeme is offline Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,033
    Total Downloaded
    0
    Removing Llams will reduce the number of possible causes, including the remote possibility of the IC for the front sensors having been damaged during the jump-start.
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
Page 1 of 9 123 ... LastLast
« New occupant of my garage | 2015 d4 fuel gauge. »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!