Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Chrysler 3-Speed ATF Level Checking

  1. #1
    Davo is offline ChatterBox Silver Subscriber
    Join Date
    May 2007
    Location
    WA
    Posts
    2,595
    Total Downloaded
    0

    Chrysler 3-Speed ATF Level Checking

    Is there a trick to this? This is why I don't like automatics. Nothing's simple. I've done the whole warm it up, shift through the gears and then check the dipstick thing, but it doesn't always have the same level on it. It depends on which way you put the dipstick down that long tube. Or sometimes it just doesn't have an even level on it. I thought I had it sussed and put a litre in today - and then found a nice puddle under the torque convertor housing drain! Any ideas?
    At any given point in time, somewhere in the world someone is working on a Land-Rover.

  2. #2
    richard4u2 Guest
    interesting , mine dribbles a little from there also ??

  3. #3
    350RRC's Avatar
    350RRC is offline ForumSage Silver Subscriber
    Join Date
    Mar 2008
    Location
    Bellarine Peninsula, Brackistan
    Posts
    5,502
    Total Downloaded
    0
    If it's any consolation I have the same prob with the C9 in my POS. No two dipstick readings the same.The only saving grace is that any excess ATF comes out a breather tube up high in the engine bay.

    DL

  4. #4
    Davo is offline ChatterBox Silver Subscriber
    Join Date
    May 2007
    Location
    WA
    Posts
    2,595
    Total Downloaded
    0
    So as long as there's some oil in there . . . ? Unfortunately, I'm not quite ready to put in an LT95 yet. That's more my level of technology.
    At any given point in time, somewhere in the world someone is working on a Land-Rover.

  5. #5
    Join Date
    Jul 2006
    Location
    Brisbane, Inner East.
    Posts
    11,178
    Total Downloaded
    0
    Long time since I owned a Torqueflite, but don't you dip them at operating temperature, idling in drive? I sort of remember the dipstick only goes in one way, like the BW35's used on later Valiants and my cook's Escort.
    URSUSMAJOR

  6. #6
    Join Date
    Jan 1970
    Location
    Yinnar South, Vic
    Posts
    9,943
    Total Downloaded
    0
    Quote Originally Posted by Brian Hjelm View Post
    Long time since I owned a Torqueflite, but don't you dip them at operating temperature, idling in drive? I sort of remember the dipstick only goes in one way, like the BW35's used on later Valiants and my cook's Escort.
    Operating temp, idling in Park

    Pretty sure idling in Drive is a good step towards natural selection

    BW35's, ewwwww

  7. #7
    Join Date
    Jul 2006
    Location
    Brisbane, Inner East.
    Posts
    11,178
    Total Downloaded
    0
    Quote Originally Posted by rovercare View Post
    Operating temp, idling in Park

    Pretty sure idling in Drive is a good step towards natural selection

    BW35's, ewwwww
    Just checked the Escort workshop manual (Ford one, three inches thick) and it definitely says idling in drive. Handbrakes are useful when doing this.
    URSUSMAJOR

  8. #8
    Join Date
    Jan 1970
    Location
    3960
    Posts
    1,161
    Total Downloaded
    0
    Handbook says , basic .

    Level ground , start , run till run temp , through all gears pause at each .

    In neutral at idle when at temp , remove and wipe blade clean , re-insert immediately withdraw and check level .

    Level must be between Full and Add 1 pint marks .

    So as long as fluid is seen between the 2 marks that all that`s needed .

    Had a look at ours and there is better than half and inch between and it also says on the stick , in neutral at temp .

    Ours hasn`t lost any oil in the last 15 yrs but in saying that it a couple of yrs since i`ve checked .

    The one with the Zf i check and service all the time and listen to it but the one with the torque flite just works away without fuss .

    I think the 2 litre Escort with the C4 is a bit like the Rover V8s and torque flite the boxes are better than what`s pushing , though the escort was no slouch.

    Cheers Peter

  9. #9
    Join Date
    Jul 2006
    Location
    Brisbane, Inner East.
    Posts
    11,178
    Total Downloaded
    0
    My cook has an Escort 1300 auto she bought new in 1972. It has the BW35. The car has travelled a genuine 112,000 miles. The 1300 is far too small an engine to pull an auto.
    URSUSMAJOR

  10. #10
    Join Date
    Apr 2009
    Location
    Crafers West South Australia
    Posts
    11,732
    Total Downloaded
    0
    Quote Originally Posted by Brian Hjelm View Post
    My cook has an Escort 1300 auto she bought new in 1972. It has the BW35. The car has travelled a genuine 112,000 miles. The 1300 is far too small an engine to pull an auto.
    OOH MY mate's wife-to-be had one, 0 to 60 in an hour or so...

    As far as the torqueflite goes, mine needed the engine running in neutral after shifting through the gears etc. So long as it read on the stick between the marks it went fine.

Page 1 of 2 12 LastLast

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!