Page 2 of 2 FirstFirst 12
Results 11 to 14 of 14

Thread: Heater blowing heat when not on!

  1. #11
    MickG's Avatar
    MickG is offline ChatterBox Silver Subscriber
    Join Date
    Jan 1970
    Location
    Gold Coast, Qld
    Posts
    2,737
    Total Downloaded
    0
    Quote Originally Posted by disconut
    I seem to recall this issue when I had mine. I did not like the hot air on start up. The service manager pointed this out. Hope it helps.

    Air distribution control
    To control the air distribution within the cabin the ATC ECU signals the servo motor controlling the distribution flaps in the heater assembly to move to the flaps to the appropriate position.
    In the automatic and economy modes, if the LH or RH temperature selections are set to LO or HI, air distribution is fixed as follows:
    If one is set to LO and one is set to a specific temperature, to face level only.
    If one is set to HI and one is set to a specific temperature, to footwells only.
    If one is set to LO and one is set to HI, to face level and footwells.
    When specific LH and RH temperature selections are set, air distribution is determined from the target air outlet
    temperatures. For higher target air outlet temperatures, air distribution is set to footwells only. For lower target air outlet temperatures, air distribution is set to face level only. For intermediate target air outlet temperatures, air distribution is set to face level and footwells. When the air distribution is set to face level and footwells, the ATC ECU varies the bias between the footwells and the face level outlets, in three stages, to provide a gradual transition of air distribution from footwells only to face level only. The three stages of bias are also employed when the air distribution is manually selected to face level and footwells.
    During warm-up, the air distribution changes to face level and footwells for a period, then reverts to footwells only.
    The period of air distribution at face level and footwells can be cancelled by pressing and holding the on/off and defrost mode switches, then turning the ignition switch from off to on.
    Pressing and holding the AUTO and defrost switches,
    then turning the ignition switch from off to on, restores the period of air distribution at face level and footwells.

    Have fun,

    Trev.

    Thanks Trev, but i'll be honest. totally lost and none the wiser
    '99 Manual TD5 D2.......heap of money spent on it and it has ended

  2. #12
    Join Date
    Jan 1970
    Location
    Brisbane, Queensland (Australia)
    Posts
    1,461
    Total Downloaded
    0
    Yep I'm lost also ... too much information. My D2 has always had heat coming from the vents unless I run the aircon. It does not seem to bother the fuel comsupmtion too much and the Td5 has plenty of grunt to run aircon. I guess the downside is that the aircon will wear out faster but at least it gets plenty of use to circulate the gas.

    I usualy run it on 22 - 24 degrees on economy mode.

  3. #13
    Join Date
    Jan 1970
    Location
    Toowoomba QLD.
    Posts
    1,179
    Total Downloaded
    0
    Basically the option is there to turn the hot air off on start up. (the orange printed bit). The owners handbook should have something similar in it.

    Trev.

  4. #14
    Join Date
    Jan 1970
    Location
    Adelaide Hills. South Australia
    Posts
    13,349
    Total Downloaded
    0
    This sort of 'defect' has been in evidence on my 95 since new. It seems to pick up heat from somewhere even when it's all off, & fresh air is coming in.
    I have checked with thermometers & it's always higher than ambient which craps me off as it means the AC has to go on.
    When the ambient (outside) air is comfortable I don't want the AC on but I need to.

    I repeatedly told the Stealers about this each time & they claimed they couldn't fault it.
    I didn't quite get the old, "But they all do that, Sir".

    It has a heating valve next to the RH cyl. bank but later models of the D1 didn't have that for some reason.

    I fitted some reflective insulation between the rear of the V8 & the bulkhead, but it made no difference. I have also wondered whether it is picking up bonnet heat & then sucking it straight into the pollen filters & then inside. Crap idea if it does.

Page 2 of 2 FirstFirst 12

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!