Results 1 to 7 of 7

Thread: RRC Disco Defer, ball joints all the same?

  1. 13th June 2008, 11:16 PM #1
    HangOver's Avatar
    HangOver
    HangOver is offline YarnMaster
    Join Date
    Jan 1970
    Location
    back in the suburbs, near joondalup
    Posts
    3,438
    Total Downloaded
    0

    RRC Disco Defer, ball joints all the same?

    Hi All
    I have 4 ball joints / rod ends

    The part numbers are:
    RTC5869G RH thread
    RTC5870L LH thread

    I have searched the internet and have found these will fit:
    RRC 86-94
    Disco 89-98
    Defer 87-

    I would like to know if these are suitable for a 81' RRC?
    Reply With Quote Reply With Quote
  2. 14th June 2008, 09:35 AM #2
    PhilipA
    PhilipA is offline Swaggie Subscriber
    Join Date
    Jan 1970
    Location
    Avoca Beach
    Posts
    14,194
    Total Downloaded
    0
    AFAIR A rangie has 2xRH as it has a little adjuster rod on the RH side with a RH thread at one end and a LH at the other.
    So you had better check them before ordering.
    Regards Philip A
    Reply With Quote Reply With Quote
  3. 14th June 2008, 10:54 AM #3
    HangOver's Avatar
    HangOver
    HangOver is offline YarnMaster
    Join Date
    Jan 1970
    Location
    back in the suburbs, near joondalup
    Posts
    3,438
    Total Downloaded
    0
    I already have them I just wanted to know if they will fit before I pull the old ones off.
    Reply With Quote Reply With Quote
  4. 14th June 2008, 02:32 PM #4
    PhilipA
    PhilipA is offline Swaggie Subscriber
    Join Date
    Jan 1970
    Location
    Avoca Beach
    Posts
    14,194
    Total Downloaded
    0
    So Have you got 3xRH and 1 x LH?
    Regards Philip A
    Reply With Quote Reply With Quote
  5. 14th June 2008, 02:35 PM #5
    PhilipA
    PhilipA is offline Swaggie Subscriber
    Join Date
    Jan 1970
    Location
    Avoca Beach
    Posts
    14,194
    Total Downloaded
    0
    Hang on there are only 3.
    The steering arm up to 93? has its own joint.
    Then across to the LH front wheel=1 RH I think
    Then the two on the steering rod behind the axle. Both RH I think.
    Regards Philip A
    Reply With Quote Reply With Quote
  6. 14th June 2008, 02:42 PM #6
    HangOver's Avatar
    HangOver
    HangOver is offline YarnMaster
    Join Date
    Jan 1970
    Location
    back in the suburbs, near joondalup
    Posts
    3,438
    Total Downloaded
    0
    I bought them cheap and I got 4 of them
    x1 RTC5869G RH thread
    x1 RTC5870L LH thread

    x1 boxed without codes
    x1 unboxedun marked
    Reply With Quote Reply With Quote
  7. 14th June 2008, 03:58 PM #7
    350RRC's Avatar
    350RRC
    350RRC is offline ForumSage Silver Subscriber
    Join Date
    Mar 2008
    Location
    Bellarine Peninsula, Brackistan
    Posts
    5,553
    Total Downloaded
    0
    Hi,

    If it has the stock track rod (at the rear of front diff) then they are all RH thread. Some HD after market track rods are LH thread on one side.

    Stock (RH thread) ball joints from Burson's are ??626 R and cost about $29 each.
    Reply With Quote Reply With Quote
« TD5 wont start | Defender, 12Volt winch cables???? »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!