Results 1 to 6 of 6

Thread: Coolant Temperature Sensor

  1. 21st October 2009, 09:38 AM #1
    V8Landy's Avatar
    V8Landy
    V8Landy is offline Wizard
    Join Date
    Jan 1970
    Location
    Colac foot of the otways
    Posts
    1,505
    Total Downloaded
    0

    Coolant Temperature Sensor

    Can some one tell me where this is on a 3.9 V8i. Trying to rule out everything that can make it run rich and idle fast. Also i looked under the left side panel for ecu but could not see it(or did not reconise it) Can some one tell me what i'm looking for. It is a 91 V8i Disco ( it has a 3.9 in it) Any help appreciated Thanks Brett
    Reply With Quote Reply With Quote
  2. 21st October 2009, 10:07 AM #2
    langy's Avatar
    langy
    langy is offline Wizard
    Join Date
    Jan 1970
    Location
    Somewhere else, QLD
    Posts
    1,863
    Total Downloaded
    0
    The EFI coolant sensor is the one with 2 prongs on it, screws into the intake manifold roughly at middle front. ( The one for the dash has only 1 prong)
    The AC sensors should be on the elbow near the thermostat.

    The ECU should be behind the kick panel next to and a little above the accelerator - big silver box with 14 cux on it.
    Reply With Quote Reply With Quote
  3. 21st October 2009, 11:32 AM #3
    Katie Guest
    The car may stay on fast idle and run rich if it has a wrong or stuck thermostat, should be 88deg. Also check the resistance between the first and last pins on the air flow metre, I think Land Rover set it at 250ohm I find some run rich at that and have had much better running below 4ohm.
    Otherwise air leaks or leaking injectors?
    Katie
    Reply With Quote Reply With Quote
  4. 21st October 2009, 02:30 PM #4
    roverv8's Avatar
    roverv8
    roverv8 is offline Master Subscriber
    Join Date
    Sep 2009
    Location
    Central Vic
    Posts
    683
    Total Downloaded
    0
    3.9 v8, I just replaced mine, it's the very front sensor on the inlet manifold, this is the sensor for the ECU, not the dashboard temp.
    It has a plug on it similar to the plugs on your petrol injectors.
    Luke
    Reply With Quote Reply With Quote
  5. 22nd October 2009, 02:22 PM #5
    V8Landy's Avatar
    V8Landy
    V8Landy is offline Wizard
    Join Date
    Jan 1970
    Location
    Colac foot of the otways
    Posts
    1,505
    Total Downloaded
    0
    Quote Originally Posted by Katie View Post
    The car may stay on fast idle and run rich if it has a wrong or stuck thermostat, should be 88deg. Also check the resistance between the first and last pins on the air flow metre, I think Land Rover set it at 250ohm I find some run rich at that and have had much better running below 4ohm.
    Otherwise air leaks or leaking injectors?
    Katie

    Tested the afm, The thermostat is fine and the right temp, Not sure on the injectors so will see how i go.
    Went for a run on petrol and it is not as rich as it was sense i have done the afm so it may be right now.
    Thanks for the info everyone. Cheers Brett
    Reply With Quote Reply With Quote
  6. 24th October 2009, 01:19 AM #6
    LOVEMYRANGIE's Avatar
    LOVEMYRANGIE
    LOVEMYRANGIE is offline YarnMaster
    Join Date
    Feb 2008
    Location
    Northern Windowlickersville WA
    Posts
    3,403
    Total Downloaded
    0
    Quote Originally Posted by Katie View Post
    The car may stay on fast idle and run rich if it has a wrong or stuck thermostat, should be 88deg. Also check the resistance between the first and last pins on the air flow metre, I think Land Rover set it at 250ohm I find some run rich at that and have had much better running below 4ohm.
    Otherwise air leaks or leaking injectors?
    Katie
    Its not set on ohms, its set on volts. The ECU reads a voltage output from the AFM.
    And 4 ohms is almost a dead short, plus if your checking it with the plug still on, you are taking into account the line resistance of the harness and also the components in both the ECU and AFM resulting in a wildly incorrect MAF setting.

    See this post. http://www.aulro.com/afvb/technical-...ml#post1092934

    Cheers

    Andrew
    Reply With Quote Reply With Quote
« TD5 Head Gasket How many Holes? | A slightly strange request »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!