Page 2 of 2 FirstFirst 12
Results 11 to 14 of 14

Thread: Timing Belt Success or Failure?

  1. 31st January 2009, 12:45 PM #11
    RichardK
    RichardK is offline ChatterBox Silver Subscriber
    Join Date
    Jan 1970
    Location
    Western Australia
    Posts
    2,955
    Total Downloaded
    0
    Pedro, because you asked most succinctly....



    With cover off



    Tool kit ready



    Seriously



    Don't forget to protect turbo inlet from foreign matter



    thermatic fan off



    EGR throttle inlet removed



    There's the belt



    The two idler pulleys, note the rubber crumbs, I assume they came from the belt but no obvious signs where



    The tensioner pulley



    Close up of tensioner



    LH camshaft sprocket



    Ooooppppps, some lamp work jewelery SWMBO makes
    RichardK

    Series IV Matrix Offroad Camper following our Discovery 3 with E Diff, BAS Remap, Mitch Hitch, Uniden UHF, Codan NGT HF, Masten TPMS, Proquip Compressor Guard, ARB Winch Bar, Milemarker Hydraulic Winch, 4x4 Intelligence Rear Wheel Carrier, VMS GPS with Rear Camera,
    Reply With Quote Reply With Quote
  2. 31st January 2009, 04:34 PM #12
    Pedro_The_Swift's Avatar
    Pedro_The_Swift
    Pedro_The_Swift is offline The MOD Father
    Join Date
    May 2003
    Location
    On The Road
    Posts
    30,031
    Total Downloaded
    0
    Thanks Richard

    I notice the only two belt aligners (is there a proper tech name?)are on the crank and RHS cam pulley,,,

    all idler and tensioners must have been OK,?,?

    take note of their numbers?
    "How long since you've visited The Good Oil?"

    '93 V8 Rossi
    '97 to '07. sold.
    '01 V8 D2
    '06 to 10. written off.
    '03 4.6 V8 HSE D2a with Tornado ECM
    '10 to '21
    '16.5 RRS SDV8
    '21 to Infinity and Beyond!

    1988 Isuzu Bus. V10 15L NA Diesel
    Home is where you park it..

    [IMG][/IMG]
    Reply With Quote Reply With Quote
  3. 31st January 2009, 05:13 PM #13
    RichardK
    RichardK is offline ChatterBox Silver Subscriber
    Join Date
    Jan 1970
    Location
    Western Australia
    Posts
    2,955
    Total Downloaded
    0
    Thats right Pedro, those are the only two aligners, I replaced the tensioner and both idlers, the tensioner comes as part of a kit together with a new bolt
    RichardK

    Series IV Matrix Offroad Camper following our Discovery 3 with E Diff, BAS Remap, Mitch Hitch, Uniden UHF, Codan NGT HF, Masten TPMS, Proquip Compressor Guard, ARB Winch Bar, Milemarker Hydraulic Winch, 4x4 Intelligence Rear Wheel Carrier, VMS GPS with Rear Camera,
    Reply With Quote Reply With Quote
  4. 31st January 2009, 07:34 PM #14
    inside's Avatar
    inside
    inside is offline Wizard Subscriber
    Join Date
    Jan 1970
    Location
    Melbourne
    Posts
    1,545
    Total Downloaded
    0
    Did you consider doing the water pump while there? I have done two quad cam engines in the past and considering the water pump usually becomes very accessible while doing the belt I always thought it was a good idea.
    Reply With Quote Reply With Quote
Page 2 of 2 FirstFirst 12
« Timing Belt change | Konis in a D3 »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!