Page 46 of 50 FirstFirst ... 364445464748 ... LastLast
Results 451 to 460 of 495

Thread: Adaptor shaft

  1. 17th March 2015, 01:56 PM #451
    Ancient Mariner
    Ancient Mariner is offline Wizard
    Join Date
    Oct 2012
    Location
    FNQ
    Posts
    1,723
    Total Downloaded
    0
    Quote Originally Posted by Vern View Post
    Hoping to send some bits and pieces and drawings to barry at hy tuff to make some adapter shafts, i will be getting 3 done for myself.
    Not sure on pricing yet though.
    For anyone with a 175mm approx adapter housing this will fit, you will need an mxa flange and a new input seal to suit.
    Who's in?
    You will also need a sleeve between end of gear and 28 spline to control end float one shot grease will mix with TC oil and being a LR will eventually finish upon the ground
    Reply With Quote Reply With Quote
  2. 17th March 2015, 02:38 PM #452
    Vern's Avatar
    Vern
    Vern is offline OldBushie
    Join Date
    May 2006
    Location
    Woolgoolga
    Posts
    7,870
    Total Downloaded
    0
    How much float is acceptable? I can make a sleeve that is 6.5mm wide (from memory) that will go between that mxa flange and the input gear which need to be pressed on to the adapter shaft.
    Or the shaft can be made to float against the msa output shaft and also the internal shoulder on the tc input gear.
    Reply With Quote Reply With Quote
  3. 17th March 2015, 07:32 PM #453
    Ancient Mariner
    Ancient Mariner is offline Wizard
    Join Date
    Oct 2012
    Location
    FNQ
    Posts
    1,723
    Total Downloaded
    0
    From the gear to the MXA flange does nothing has to be to from gear to shaft.I kept my end float to about.010" but not really critical .That 6.5mm could be a bit of neoprene hose to slow grease migration Make your sleeve longer than you need and trim on assembly just make sure you have some float

    Noel
    Reply With Quote Reply With Quote
  4. 17th March 2015, 07:57 PM #454
    Vern's Avatar
    Vern
    Vern is offline OldBushie
    Join Date
    May 2006
    Location
    Woolgoolga
    Posts
    7,870
    Total Downloaded
    0
    The 6.5mm bit of neoprene you speak of, I thought to make from steel that will press on the shaft for end float and have a fibre washer (like on the lt230 output flanges) to control grease migrating?
    Is this stupid noel?
    Reply With Quote Reply With Quote
  5. 17th March 2015, 08:30 PM #455
    Ancient Mariner
    Ancient Mariner is offline Wizard
    Join Date
    Oct 2012
    Location
    FNQ
    Posts
    1,723
    Total Downloaded
    0
    Not stupid but no give with fibre so end float is a gap between the two
    Reply With Quote Reply With Quote
  6. 17th March 2015, 09:51 PM #456
    Vern's Avatar
    Vern
    Vern is offline OldBushie
    Join Date
    May 2006
    Location
    Woolgoolga
    Posts
    7,870
    Total Downloaded
    0
    Sorry meant felt, not fibre
    Reply With Quote Reply With Quote
  7. 11th May 2015, 07:52 PM #457
    Ancient Mariner
    Ancient Mariner is offline Wizard
    Join Date
    Oct 2012
    Location
    FNQ
    Posts
    1,723
    Total Downloaded
    0
    Play time on my new toy
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  8. 11th May 2015, 08:36 PM #458
    Vern's Avatar
    Vern
    Vern is offline OldBushie
    Join Date
    May 2006
    Location
    Woolgoolga
    Posts
    7,870
    Total Downloaded
    0
    No body likes a smart ass noel
    Reply With Quote Reply With Quote
  9. 12th May 2015, 06:57 AM #459
    Vern's Avatar
    Vern
    Vern is offline OldBushie
    Join Date
    May 2006
    Location
    Woolgoolga
    Posts
    7,870
    Total Downloaded
    0
    What are you making them out of Noel??
    Reply With Quote Reply With Quote
  10. 12th May 2015, 05:34 PM #460
    Lotz-A-Landies's Avatar
    Lotz-A-Landies
    Lotz-A-Landies is offline Super Moderator Gold Subscriber
    Join Date
    Jul 2006
    Location
    East-South-East Girt-By-Sea
    Posts
    17,662
    Total Downloaded
    1.20 MB
    Hi Noel

    Are you going to have a female-female adapter* on the MSA/MXA or are you still going to use the prop shaft flanges?

    Diana

    * Like on the MT82 http://www.aulro.com/afvb/90-110-130...ter-shaft.html

    You won't find me on: faceplant; Scipe; Infragam; LumpedIn; ShapCnat or Twitting. I'm just not that interesting.
    Reply With Quote Reply With Quote
Page 46 of 50 FirstFirst ... 364445464748 ... LastLast
« 4bd1/lt85 clutch push rod | In need of a new LT230 »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!