Thread: Fitting the Traxide Lighting Upgrade and Driving Light Kit to a 2007+

Forgive me if I misunderstand.

I take it you want to be able to operate the driving lights independently of the high beam.

A word of caution if this is the case:

Regulation requires that the driving lights must be dimmable with the high beam lights which is why the Traxide kit is configured this way.

A dumb question:

Why do you want to do this?

You're forgiven . I specifically want to comply and have the Driving lights activate only when high beam is on.

When looking at the wiring diagram and the suggestion from drivesafe (to modify his normal kit to work with the negatively switched LandRover switch), it appears to me that in that configuration the lights would indeed be able to operate without high beam being active.

I may well be mistaken, which is why I am asking the question.
There are no dumb questions!

I hope this clarifies things?!

Ah so...it's about getting the switch to light up:

I've failed this test but haven't persevered.

I can get the amber LED to illuminate when the driving lights are on but haven't pursuaded the green switch light to show up with the rest of the switches when they are illuminated.

I did purchase a socket to fit the back of the switch to make life easier but the wiring puzzle eludes me.

The challenge is the switch itself - it is negative switching. The pins are below:

1 = earth switched
2 = +ve illumination (on with sidelights)
3 = earth
4 = earth (matches pin 3)
5 = +ve control light (small orange led, feed from powered device)

When the button is pressed, it joins (1) & (4) and closes a circuit with 5 (see pic below).

With the dual headlight relay, S1 & S2 are the switches for L1/L2. The normal relay has these attached to the HB via a switch and a constant earth (S). You need to change this, making the earth the switch not S2/S2 (which are linked to the H.

To make the switch work - you tap (4) into the dash earth header and use (1) as the relay's -ve and have the high beam from the headlight relay providing +ve to activate the driving light relay. Press the button, closes the earth switch, powering the relay.

If you connect a wire from the DL (L1) to (5), the orange led will glow when the DL has power. If you connect (2) to the dash illumination, the switch will light up when the dash lights up.

Lookie here for a butchered traxide diagram.


Not my own work - I found a bunch of people who have struggled with this - most comprehensive post is here Defender2 - View topic - Switch fascia ... It did take me a handful of 10A fuses and an hour or so to put it all together for the Dual headlight relay

Thanks Willie. Your diagram corresponds pretty much with what I envisioned. That gives me great confidence!

Unfortunately I didn't get the chance to get the driving lights in on the weekend. When crawling under the car to work out the best cable route from the battery, I noticed an oil leak between the gearbox and the transfer case. I didn't want to touch too much until I got it back to the dealer for repairs as I've only got about 1000k on the clock so far! (A lot further than some other people, but still.....).

Originally Posted by dmdigital

Interesting...I'm somewhat

I thought this was YUG000540LNF


Can I ask where you got it from?

Can anyone suggest where in Aust.to get the female plugs that fit these switches. I have tried searching but I am having trouble working out exactly which plug it is and whether I also need to get special terminals to fit in the plastic holder (that then plugs into the switch). Also places I have found on-line only seem to sell these types of plugs in bulk packs.

Thought about just soldering on wires direct to switch but there is not much room and I am worried about melting the plastic or ending up with a short circuit.

I don't know where in Australia, but I got mine from the UK:
Dingocroft (Penn Rental Service Ltd t/a) Electrical Miscellany

Part number: ZZplug01

I bought two of them when I got mine, and I believe there would be no problems if you only want one.
The part comes with the plastic insert to fit the back of the switch and also the lugs to terminate on the end of your wires to suit.

Thanks. A sets of two is perfect....I got two switches just in case i needed more lights.