Page 3 of 3 FirstFirst 123
Results 21 to 27 of 27

Thread: Discovery 2a Custom Rear Door Card

  1. 7th February 2015, 05:31 PM #21
    Ghost perch
    Ghost perch is offline Fossicker
    Join Date
    Dec 2014
    Location
    Hobart
    Posts
    14
    Total Downloaded
    0
    Thanks mate but i am happy with doing it this way, you dont have to be a member of the forum to view images this way.
    So a little more progress, finally got my hands on the sheet and got it all cut out. The main rear panel is done just needs to be cleaned up and powder coated. The slide shelf has had its hinge added for test fitting. Tomorrow i should be able to get it all knocked together in a test fit.
    Cheers Rob.






    Reply With Quote Reply With Quote
  2. 7th February 2015, 06:09 PM #22
    iPom's Avatar
    iPom
    iPom is offline Master Subscriber
    Join Date
    Apr 2010
    Location
    South East Queensland near the sea...
    Posts
    796
    Total Downloaded
    0
    Looks very neat Rob ... Thanks for the update
    TRS Chip ,D2a I/c, Silcone Hoses, EMS2, 2" Lift, BFG KM2s, QT Diff Guards, 4X4 DE Guard, Shadow Bar. VRS Winch, LR Light Guards, .50 CDL, Provent 200, Slickrock Disconnects, Rovadrive Sump, G4 Roof Rails, D2a SLABS ECU, APT Sliders.DBA Rotors. ABS Ext.
    Reply With Quote Reply With Quote
  3. 13th February 2015, 07:07 PM #23
    Ghost perch
    Ghost perch is offline Fossicker
    Join Date
    Dec 2014
    Location
    Hobart
    Posts
    14
    Total Downloaded
    0
    Progress has slowed as lack of free time with work. Just a few little things to finish now tho.
    I used some door seal rubber to stop any noise in the bench while folded up, also some ute tie down fixings to keep it closed.
    Next jobs on the list.
    1. Replace the 400lb mono single strut with some nylon coated stainless wire.
    2. work out a locking system to keep the slide out when facing up hill,
    may replace the slides with locking ones. Had the slides sitting around home so used them for now.


    Reply With Quote Reply With Quote
  4. 13th February 2015, 07:11 PM #24
    iPom's Avatar
    iPom
    iPom is offline Master Subscriber
    Join Date
    Apr 2010
    Location
    South East Queensland near the sea...
    Posts
    796
    Total Downloaded
    0
    Good stuff Rob, anymore photos of the slides etc
    TRS Chip ,D2a I/c, Silcone Hoses, EMS2, 2" Lift, BFG KM2s, QT Diff Guards, 4X4 DE Guard, Shadow Bar. VRS Winch, LR Light Guards, .50 CDL, Provent 200, Slickrock Disconnects, Rovadrive Sump, G4 Roof Rails, D2a SLABS ECU, APT Sliders.DBA Rotors. ABS Ext.
    Reply With Quote Reply With Quote
  5. 13th February 2015, 07:15 PM #25
    Ghost perch
    Ghost perch is offline Fossicker
    Join Date
    Dec 2014
    Location
    Hobart
    Posts
    14
    Total Downloaded
    0
    Cheers iPom Have not got any ill take some more in the morning, not much light here at the moment.
    Reply With Quote Reply With Quote
  6. 13th February 2015, 07:32 PM #26
    iPom's Avatar
    iPom
    iPom is offline Master Subscriber
    Join Date
    Apr 2010
    Location
    South East Queensland near the sea...
    Posts
    796
    Total Downloaded
    0
    No worries Rob ... appreciated
    TRS Chip ,D2a I/c, Silcone Hoses, EMS2, 2" Lift, BFG KM2s, QT Diff Guards, 4X4 DE Guard, Shadow Bar. VRS Winch, LR Light Guards, .50 CDL, Provent 200, Slickrock Disconnects, Rovadrive Sump, G4 Roof Rails, D2a SLABS ECU, APT Sliders.DBA Rotors. ABS Ext.
    Reply With Quote Reply With Quote
  7. 14th February 2015, 05:02 PM #27
    gavinwibrow's Avatar
    gavinwibrow
    gavinwibrow is offline YarnMaster Silver Subscriber
    Join Date
    Oct 2011
    Location
    Fremantle WA
    Posts
    3,838
    Total Downloaded
    0
    Quote Originally Posted by Ghost perch View Post
    Back on topic....
    Still waiting for the sheet to turn up, you have to love Tasmanian freight service.
    So in the mean time i got to work inserting the M6 rivnuts (14 in total). I cant get over how handy they are to use. Didn't worry about the tool just used a bolt, nut and washer.





    Cheers Rob.
    Great job. Which type of M6 rivnuts did you use eg s/s, alloy etc and smooth, knurled or? I'm about to re-seat my checkerplate version and replace the marginal at best original style plastic pushins.
    D4 MY16 TDV6 - Cambo towing magic, Traxide Batteries, X Lifter, GAP ID Tool, Snorkel, Mitch Hitch, Clearview Mirrors, F&R Dashcams, CB
    RRC MY95 LSE Vogue Softdash "Bessie" with MY99 TD5 and 4HP24 transplants
    SADLY SOLD MY04 D2a TD5 auto and MY10 D4 2.7 both with lots of goodies
    Reply With Quote Reply With Quote
Page 3 of 3 FirstFirst 123
« Fitting Snorkel to 300 Tdi Defender | D4 Rear Storage Project including drop fridge slide - Part 1 »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!