Thread: What did you do on your Landy today?

Two days? Pfft
I drove mine to work and back today
Ordering some 7100s and associated bits next week

Sent from my HTC One using AULRO mobile app

Originally Posted by Disco Muppet

Two days? Pfft
I drove mine to work and back today
Ordering some 7100s and associated bits next week

Sent from my HTC One using AULRO mobile app

I drove mine to work and back and down the local IGA.

Went for a drive tonight. Got a flat tyre. Got the living shyte scared out of me by a huge roo standing not 3 metres from me while i was changing the tyre in the bush on a dirt road. Just heard a thump as i was standing on the wheel brace in the almost pitch dark. Looked around with light on on the phone and there it was, looking at me. I jumped and when i fell back to earth a minor earth quake ensued and i yelled at it and ran towards it and it took off. Thank goodness. That got the heart rate up and the adrenalin going. I did a F1 speed wheel change almost i reckon. I took a couple pics of the lights on the s3.
No.1 low beam (sealed beams)
No.2 high beam with 2x6" light bars below headlights and 1x50" light bar above roof. Like daylight for about 400 metres.
Both were taken with the old 186 ticking over at about 450 rpm.
I took the pics after the heart rate was back to normal. Drove home. No further incidents.

Cheers Rod.

Tyre that went flat is the one i fixed the other day. Bugga.


Sent from my GT-I9507 using AULRO mobile app

Servicing the 2a and cleaning it up a bit for the Expo.

Actually started yesterday. First step was to put the front wheels up on ramps, and pressure wash underneath to remove most of the cow dung and mud. Let that dry off a bit and moved it onto the concrete. Then put all four corners on stands, and removed the wheels.

Then pressure washed it again to remove some of the stuff. The cow dung is certainly sticky, and dries better than the paint.

Drained engine oil, replaced filter, serviced air cleaner. Removed rocker cover, and adjusted tappets. No sign of valve seat recession, all tappets needed about 1/10 of as turn tightening (valve seat recession would be shown by closing gaps). Replaced rocker cover and fixed the leak in the petrol pipe resulting from disturbing the hose fitting on the in line filter. (The pipe is clamped under the front bolt on the rocker cover.) Checked ignition timing. Checked condition of points and gap.

Checked and topped up swivels, front and rear axles, gearbox, transfer case, steering box, hydraulic reservoir. Greased clutch pivot, handbrake relay pivot, four U-joints and two sliding joints. Checked all spring bushes, tie rod ends, U-bolts. Used high lift jack to take weight of springs, and painted springs with a mixture of oil and turps.

Adjusted brakes. Adjusted handbrake. Inspected all brake drums for signs of oil or brake fluid. Topped up radiator. Topped up washer reservoir. Straightened step on driver's side. Removed front prop shaft to replace damaged boot on sliding joint. Found front bolts loose. Will get new bolts and nyloc nuts tomorrow, so it is still off.

Still quite a bit to do.

John

That's a fair day's work. I'm sad that I will miss this years Expo.

Changed the front lower Hydro bushes.
Rides beautifully.

Finished service on the 2a (more or less). Prop shaft back on, checked oil level in overdrive, cleaned some more mud and cow dung off underneath, put wheels back on, took it off stands. Still to clean up inside of cab, oil door hinges and throttle linkage, drilube on door locks, check all lights operating, clean windows.

John

I repaired a previously repaired puncture on the s3. Ended up fitting a new tube. The tyre has good tread but the tyre bead area is a bit ratty. The tyres are remoulds not retreads and i bought them of ebay a while ago for $1.00, or actually 0.99cents, For 4 tyres on rims. So good value i think if i can wear them out on the s3 which was really only bought as a spare parts car but it was way better than the s2a i am doing up, see my betsy rebuild thread. I thought id just have some fun in it, but im actually enjoying it heaps.

I also fitted a roaded (less than 400km) dunlop road gripper 750 x 16 to a disco 1 rim in a tubeless configuration to see what they look like. They seem to fit ok. I have 5 of these tyres and 6 x d1 rims so i might see how they fit on the s3 and how they perform as tubeless tyres. I noted the tyre has tube type on it so i spoke to the tyre mob and they said tubeless was ok. Tube type tyres are smooth inside so the tube doesnt rub through on the inside of the tyre. So im hoping they will be good coz i actually bought them for the 2a.

Land Rover....im lovin it..

Cheers Rod

Sent from my GT-I9507 using AULRO mobile app