Page 1 of 2 12 LastLast
Results 1 to 10 of 17

Thread: Got Creative with angle Grinder , ScorpionFlares Finally done.

  1. 17th August 2008, 02:05 PM #1
    Disco_owner's Avatar
    Disco_owner
    Disco_owner is offline YarnMaster Subscriber
    Join Date
    Dec 2006
    Location
    NSW , Pennant Hills
    Posts
    3,477
    Total Downloaded
    0

    Got Creative with angle Grinder , ScorpionFlares Finally done.

    I ordered the Scorpion Flares a while back and been sitting in the Garage , been meaning to put them on for a while , I Finally got around to it, you don't wanna know how much of the panels had to be removed


    .........alright Matt ( rovercare ) you asked for Pics , here they are








    The back ones don't line up properly , had to be use the misus's haridryer and even then they still don't sit properly, but I will fix them , still needs a lot of finishing Touches , the Rubber strip has to go on yet ..






    Edit ...

    The Side Strips were taken off , they are going to get replaced with aluminum checker plate , cut and fitted by yours truely.

    It's a good thing I'm not charging by the hour .....
    Reply With Quote Reply With Quote
  2. 17th August 2008, 02:09 PM #2
    Slunnie's Avatar
    Slunnie
    Slunnie is offline Swaggie Gold Subscriber
    Join Date
    Jan 1970
    Location
    Central West NSW
    Posts
    14,147
    Total Downloaded
    99.87 MB
    Nice! Well done.

    How much came out of the guards, and how did you deal with the insides of the rear doors?
    Cheers
    Slunnie


    ~ Discovery II Td5 ~ Discovery 3dr V8 ~ Series IIa 6cyl ute ~ Series II V8 ute ~
    Reply With Quote Reply With Quote
  3. 17th August 2008, 02:28 PM #3
    Disco_owner's Avatar
    Disco_owner
    Disco_owner is offline YarnMaster Subscriber
    Join Date
    Dec 2006
    Location
    NSW , Pennant Hills
    Posts
    3,477
    Total Downloaded
    0
    Quote Originally Posted by Slunnie View Post
    Nice! Well done.

    How much came out of the guards,



    That's how Much

    Quote Originally Posted by Slunnie View Post
    and how did you deal with the insides of the rear doors?

    I haven't





    Not yet anyway , i'm not sure what I'll do yet ???

    I might Fill the gap up with Sikaflex or some sort of filler . any ideas?
    Reply With Quote Reply With Quote
  4. 17th August 2008, 08:12 PM #4
    rovercare's Avatar
    rovercare
    rovercare is offline OldBushie
    Join Date
    Jan 1970
    Location
    Yinnar South, Vic
    Posts
    9,943
    Total Downloaded
    0
    Bout time, where's the pics of the rangie?
    Reply With Quote Reply With Quote
  5. 17th August 2008, 08:34 PM #5
    Disco_owner's Avatar
    Disco_owner
    Disco_owner is offline YarnMaster Subscriber
    Join Date
    Dec 2006
    Location
    NSW , Pennant Hills
    Posts
    3,477
    Total Downloaded
    0
    Quote Originally Posted by rovercare View Post
    Bout time, where's the pics of the rangie?

    hahahah , Karl should be back from his nice little break tomorrow , so I'm going down there to take some pics in the morning


    Rangie's locked up inside the garage , so can't get pics of it


    what do ya reckon about the Scorpion Flares ?


    What should I do with the Big Gaps inside the rear Doors ????
    Reply With Quote Reply With Quote
  6. 17th August 2008, 08:48 PM #6
    V8Landy's Avatar
    V8Landy
    V8Landy is offline Wizard
    Join Date
    Jan 1970
    Location
    Colac foot of the otways
    Posts
    1,505
    Total Downloaded
    0
    Selleys no more gaps
    Looking nice Khossie about time you got off your ring
    Reply With Quote Reply With Quote
  7. 17th August 2008, 08:49 PM #7
    rovercare's Avatar
    rovercare
    rovercare is offline OldBushie
    Join Date
    Jan 1970
    Location
    Yinnar South, Vic
    Posts
    9,943
    Total Downloaded
    0
    Quote Originally Posted by Disco_owner View Post
    hahahah , Karl should be back from his nice little break tomorrow , so I'm going down there to take some pics in the morning


    Rangie's locked up inside the garage , so can't get pics of it


    what do ya reckon about the Scorpion Flares ?


    What should I do with the Big Gaps inside the rear Doors ????


    what do you do with them Gaps?????
    The scorpion flares are better than LRA as they don;t break, my mate proved that after smashing his rear door into a tree and the flare didn;t break

    I've neber had to fill the gaps as I've only fitted LRA flares, which have a moulded inner, BUT looking at that and ones I;ve seen, I'd get some aluminium, bend it up to fill most of the void and sikaflex it in
    Reply With Quote Reply With Quote
  8. 17th August 2008, 08:54 PM #8
    Slunnie's Avatar
    Slunnie
    Slunnie is offline Swaggie Gold Subscriber
    Join Date
    Jan 1970
    Location
    Central West NSW
    Posts
    14,147
    Total Downloaded
    99.87 MB
    If its any help, thats how I did mine. Except I tabbed the door and folded the tabs back onto some aluminium angle that was rivetted to the inside of the gap.

    http://www.slunnie.com/phpBB/viewtop...5b615f008e2e4d
    Cheers
    Slunnie


    ~ Discovery II Td5 ~ Discovery 3dr V8 ~ Series IIa 6cyl ute ~ Series II V8 ute ~
    Reply With Quote Reply With Quote
  9. 17th August 2008, 09:05 PM #9
    Disco_owner's Avatar
    Disco_owner
    Disco_owner is offline YarnMaster Subscriber
    Join Date
    Dec 2006
    Location
    NSW , Pennant Hills
    Posts
    3,477
    Total Downloaded
    0
    Quote Originally Posted by Slunnie View Post
    If its any help, thats how I did mine. Except I tabbed the door and folded the tabs back onto some aluminium angle that was rivetted to the inside of the gap.

    http://www.slunnie.com/phpBB/viewtop...5b615f008e2e4d


    Thanks Slunnie

    But fairdinkum , I have to use magnifying glass to see your pics.
    Reply With Quote Reply With Quote
  10. 17th August 2008, 09:09 PM #10
    Slunnie's Avatar
    Slunnie
    Slunnie is offline Swaggie Gold Subscriber
    Join Date
    Jan 1970
    Location
    Central West NSW
    Posts
    14,147
    Total Downloaded
    99.87 MB
    Yeah sorry. They are small for loading times and I was too lazy to make each pic link to a full size.

    The pics are all available in the gallery and can be clicked on for a larger 640x480 image. Sorry.

    http://www.slunnie.com/coppermine/th...s.php?album=21
    Cheers
    Slunnie


    ~ Discovery II Td5 ~ Discovery 3dr V8 ~ Series IIa 6cyl ute ~ Series II V8 ute ~
    Reply With Quote Reply With Quote
Page 1 of 2 12 LastLast
« Cleaning lasers | Tuning a carbie - Gas Analyser »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!