Page 5 of 9 FirstFirst ... 34567 ... LastLast
Results 41 to 50 of 82

Thread: Rossco. 1953 80inch 2L

  1. 1st September 2020, 07:45 PM #41
    whitehillbilly64's Avatar
    whitehillbilly64
    whitehillbilly64 is offline ChatterBox Gold Subscriber
    Join Date
    Oct 2014
    Location
    Northern NSW.Australia
    Posts
    2,023
    Total Downloaded
    0
    Good Evening.
    Mystery bolt removed. Not over tight. Banjo bolt screwed in by hand. Nothing damaged. PO probably put in hand tight and gentle nip.
    Sump plug rounded and a PITA to remove. Sized down once out. No Nasties in engine oil. New oil in.
    Cranking engine, oil pumps to head.
    Fitting starter must have been a after thought, once lower banjo bolt hole had been located and threaded. ????

    whitehillbilly
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  2. 1st September 2020, 07:46 PM #42
    whitehillbilly64's Avatar
    whitehillbilly64
    whitehillbilly64 is offline ChatterBox Gold Subscriber
    Join Date
    Oct 2014
    Location
    Northern NSW.Australia
    Posts
    2,023
    Total Downloaded
    0
    few more Pics
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  3. 14th September 2020, 06:45 PM #43
    whitehillbilly64's Avatar
    whitehillbilly64
    whitehillbilly64 is offline ChatterBox Gold Subscriber
    Join Date
    Oct 2014
    Location
    Northern NSW.Australia
    Posts
    2,023
    Total Downloaded
    0

    bits

    Pick up some bits over the weekend.
    Thanks W.
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  4. 27th September 2020, 07:25 PM #44
    whitehillbilly64's Avatar
    whitehillbilly64
    whitehillbilly64 is offline ChatterBox Gold Subscriber
    Join Date
    Oct 2014
    Location
    Northern NSW.Australia
    Posts
    2,023
    Total Downloaded
    0
    Good Morning.
    Pick up a complete but worn nut, steering box from BSF. (Thanks)
    Showed a old engineering mate this idea.
    http://morganownersclub.com.au/Remov...GWHOLj1oCDHjxY
    No problem was his reply.
    Took about an hr. 99% zinc
    All play removed. 5mm free play on outer edge of steering wheel. Play in drop arm shaft button.
    SAE 250 going into the box. His suggestion, as he uses it in steering boxes in his old Dodges. Most have wooden spoked wheels.
    What size modern oil seal replaces the old, double leather drop arm shaft ones ????
    Thanks.


    whitehillbilly
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  5. 9th October 2020, 06:54 PM #45
    whitehillbilly64's Avatar
    whitehillbilly64
    whitehillbilly64 is offline ChatterBox Gold Subscriber
    Join Date
    Oct 2014
    Location
    Northern NSW.Australia
    Posts
    2,023
    Total Downloaded
    0
    Good evening.
    Bit of work on replacement Chassis.
    Where should I stamp bulkhead plate number on Chassis on my 53 80inch. Anned and Thompson badged ?
    LH engine mount. LH front spring hanger outer side ?
    Thanks for comments.

    whitehillbilly
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  6. 9th October 2020, 07:46 PM #46
    Larry's Avatar
    Larry
    Larry is offline Wizard Subscriber
    Join Date
    Jan 1970
    Location
    Sydney
    Posts
    1,374
    Total Downloaded
    0
    My '51 chassis number is on top by the LH engine mount.
    I believe most are there.
    '51 Series 1 80"
    '12 Defender 90

    Reply With Quote Reply With Quote
  7. 19th October 2020, 03:26 PM #47
    whitehillbilly64's Avatar
    whitehillbilly64
    whitehillbilly64 is offline ChatterBox Gold Subscriber
    Join Date
    Oct 2014
    Location
    Northern NSW.Australia
    Posts
    2,023
    Total Downloaded
    0

    Few small repairs.

    Few small chassis repairs done.
    Tear in Chassis.

    whitehillbilly
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  8. 19th October 2020, 03:29 PM #48
    whitehillbilly64's Avatar
    whitehillbilly64
    whitehillbilly64 is offline ChatterBox Gold Subscriber
    Join Date
    Oct 2014
    Location
    Northern NSW.Australia
    Posts
    2,023
    Total Downloaded
    0
    Another one.
    Not sure what this was ???? Some sort of bracket ripped out. Brake line bracket on other side.
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  9. 19th October 2020, 03:35 PM #49
    whitehillbilly64's Avatar
    whitehillbilly64
    whitehillbilly64 is offline ChatterBox Gold Subscriber
    Join Date
    Oct 2014
    Location
    Northern NSW.Australia
    Posts
    2,023
    Total Downloaded
    0
    Inspection hole for Chassis repair ????
    I put a camera in side. Looks good.
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  10. 19th October 2020, 03:41 PM #50
    whitehillbilly64's Avatar
    whitehillbilly64
    whitehillbilly64 is offline ChatterBox Gold Subscriber
    Join Date
    Oct 2014
    Location
    Northern NSW.Australia
    Posts
    2,023
    Total Downloaded
    0
    Small rust hole in rear cross member.
    Cut out, new low drain hole should remove future issues.
    Attached Images Attached Images
    Reply With Quote Reply With Quote
Page 5 of 9 FirstFirst ... 34567 ... LastLast
« S1 2L Spread Bore Oil Galleries | Wanted - Hood Stick Kit 86" »

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!