Page 25 of 51 FirstFirst ... 15232425262735 ... LastLast
Results 241 to 250 of 508

Thread: Bundalenes Daughters 130 repair job

  1. 5th November 2009, 12:00 AM #241
    EchiDna's Avatar
    EchiDna
    EchiDna is offline Wizard
    Join Date
    Jan 1970
    Location
    Singapore via Melbourne
    Posts
    1,938
    Total Downloaded
    0
    not to denigrate the great work you guys are doing, but something about the front hoop on the tray being black and the horizontals and rear hoop being white just doesn't look right... either all black or all white I say

    yeah I know a bit like the non-matching mirrors from earlier in the thread
    Reply With Quote Reply With Quote
  2. 5th November 2009, 08:17 AM #242
    andrew e
    andrew e is offline Wizard
    Join Date
    Nov 2006
    Location
    narellan, sydney
    Posts
    1,131
    Total Downloaded
    0
    double post
    Reply With Quote Reply With Quote
  3. 5th November 2009, 08:25 AM #243
    andrew e
    andrew e is offline Wizard
    Join Date
    Nov 2006
    Location
    narellan, sydney
    Posts
    1,131
    Total Downloaded
    0
    Quote Originally Posted by EchiDna View Post
    not to denigrate the great work you guys are doing, but something about the front hoop on the tray being black and the horizontals and rear hoop being white just doesn't look right... either all black or all white I say

    yeah I know a bit like the non-matching mirrors from earlier in the thread
    The tray, roofracks, scrub-bars, rear flairs etc have not been painted yet. The tray has only been done in POR15. They will all be white at the end.


    Andy
    Reply With Quote Reply With Quote
  4. 5th November 2009, 04:49 PM #244
    Bundalene's Avatar
    Bundalene
    Bundalene is offline ChatterBox Gold Subscriber
    Join Date
    May 2008
    Location
    Horsley Park, Sydney
    Posts
    2,939
    Total Downloaded
    0
    Today:

    Primer - hi-filled the snorkel




    Installed the lower door rubbers - these are attached to the inside of the rock sliders. The pic below shows the door rubber with the small rivets holding the rubber to an alunimium plate and the larger rivets attaching the plate to the sliders.





    lower door seal completed. The above pic is of the rear door seal, this one is the front. I have a similar set up on our Defender and they seal well.



    Installed the guard tops





    More work on the rear tray cover




    Erich
    Reply With Quote Reply With Quote
  5. 5th November 2009, 09:14 PM #245
    EchiDna's Avatar
    EchiDna
    EchiDna is offline Wizard
    Join Date
    Jan 1970
    Location
    Singapore via Melbourne
    Posts
    1,938
    Total Downloaded
    0
    good stuff all round

    hmm enquiring minds and all that - what's por15 worth there? $64 a litre in Melb from the distro :O
    Reply With Quote Reply With Quote
  6. 5th November 2009, 09:43 PM #246
    dullbird's Avatar
    dullbird
    dullbird is offline Admin Gold Subscriber
    Join Date
    Jan 1970
    Location
    Down the road from Sydney
    Posts
    14,702
    Total Downloaded
    0
    Looking great guys

    However looking at the last photo i'm very surprised that you haven't fitted rear LED's to the tail lights would be way more durable then a bulb in those conditions up there
    Our Land Rover does not leak oil! it just marks its territory.......



    Reply With Quote Reply With Quote
  7. 5th November 2009, 09:49 PM #247
    rovercare's Avatar
    rovercare
    rovercare is offline OldBushie
    Join Date
    Jan 1970
    Location
    Yinnar South, Vic
    Posts
    9,943
    Total Downloaded
    0
    All I can add is.........****ing awseome build
    Reply With Quote Reply With Quote
  8. 5th November 2009, 09:54 PM #248
    Bundalene's Avatar
    Bundalene
    Bundalene is offline ChatterBox Gold Subscriber
    Join Date
    May 2008
    Location
    Horsley Park, Sydney
    Posts
    2,939
    Total Downloaded
    0
    Quote Originally Posted by dullbird View Post
    Looking great guys

    However looking at the last photo i'm very surprised that you haven't fitted rear LED's to the tail lights would be way more durable then a bulb in those conditions up there
    The LEDs aren't connected yet as the tray has to come off again. We are driving the 130 around with the original lights temporarily hooked up. These will disappear soon.

    Having said that, the globes in the round lights are actually LEDs

    Erich
    Reply With Quote Reply With Quote
  9. 6th November 2009, 01:47 PM #249
    Bundalene's Avatar
    Bundalene
    Bundalene is offline ChatterBox Gold Subscriber
    Join Date
    May 2008
    Location
    Horsley Park, Sydney
    Posts
    2,939
    Total Downloaded
    0
    Quote Originally Posted by EchiDna View Post
    good stuff all round

    hmm enquiring minds and all that - what's por15 worth there? $64 a litre in Melb from the distro :O

    Thanks for the comment

    $64 a litre is a good price. Wish I could get it locally for that. Our nearest supplier charges just over $80 a litre.

    Erich
    Reply With Quote Reply With Quote
  10. 6th November 2009, 02:32 PM #250
    Bundalene's Avatar
    Bundalene
    Bundalene is offline ChatterBox Gold Subscriber
    Join Date
    May 2008
    Location
    Horsley Park, Sydney
    Posts
    2,939
    Total Downloaded
    0
    We are considering shortening the panard rod by about 20mm or so (actually making a new one - possible adjustable) as the front right wheel is about 25mm further out than the front left. Does anyone have any thoughts on this.

    Erich
    Reply With Quote Reply With Quote
Page 25 of 51 FirstFirst ... 15232425262735 ... LastLast
« Adding Air Con - Bulkhead Install (TD,TDI,?) | CAL415s comp truck project. »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!